ASTM D3802 PDF

ASTM D Standard Test Method for Ball-Pan Hardness of Activated Carbon. Standard Test Method for Ball-Pan Hardness of Activated Carbon. Status: Withdrawn · Replaced by: ASTM D Buy this standard. Price: SEK. PDF. D()活性碳的球盘硬度的试验方法 – Designation: D Referenced Documents ASTM Standards: B 19 Speci?cation for.

Author: Aranos Zolozshura
Country: Singapore
Language: English (Spanish)
Genre: History
Published (Last): 6 June 2008
Pages: 131
PDF File Size: 2.32 Mb
ePub File Size: 16.74 Mb
ISBN: 774-2-60334-686-5
Downloads: 37650
Price: Free* [*Free Regsitration Required]
Uploader: Dougami

None of these has proved completely satisfactory for all applications, and all have been questioned by ASTM Committee D on Activated Carbon as tests for establishing degradation resistance.

Standard Test Method for Ball-Pan Hardness of Activated Carbon

Tyler Model SB, available from W. A superscript epsilon e indicates an editorial change since the last revision or reapproval. At the end of this period, the amount of particle size degradation is determined by measuring the quantity of carbon, by weight, which is retained on a sieve whose openings are closest to one half the openings of the sieve that de?

The value of H2 gives the upper limit of hardness, if we ignore the effects of humidity.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Place the hardness test sieve on top of the receiving pan. Apparatus and Materials 6.

  L27 ORTHOGONAL ARRAY PDF

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Weigh to the nearest 0.

ASTM D – 16 – Standard Test Method for Ball-Pan Hardness of Activated Carbon

Precision and Bias Humidity effects during a given test will largely cancel out if no change in humidity occurs between 9. The extra sieves, in this case, serve only to form a stack which?

Adjust the bottom stops to give a clearance of approximately 1. Individual reprints single or multiple astk of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Fit the cover plate with a cork stopper which extends from 3.

BoxGastonia, NChas been found to be satisfactory.

ASTM D – 10 Standard Test Method for Ball-Pan Hardness of Activated Carbon

Summary of Test Method 4. Discard the fractions above the larger and below the smaller nominal particle size. Pour the screened and weighed sample into the hardness pan and add the steel balls.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Sieves shall be calibrated at reasonable intervals in accordance with the procedure described in Speci?

  HP DESKJET D4260 MANUAL PDF

One supplier tested 31 samples of a single grade of carbon and obtained an average hardness of Table d8302 lists the hardness test sieve corresponding to each minimum nominal sieve. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The adhesion of material to sieves, brushes, etc.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Obtain at least mL of material within the nominal mesh size range.

Shake with the hammer operating for 10 min 6 10 s. Current edition approved June 29, Conceding the fact that the test does not actually measure in-service resistance to astn, it can be used to establish the comparability of lots atsm of the same grade of carbon.

Use additional material obtained as in 9. A number in 3d802 indicates the year of last reapproval.